View RSS Feed

Blennymower

Pictures of my tank

Rate this Entry
10 Comments
by
Blennymower
, 10-13-2010 at 08:27 PM (5157 Views)
Here are pictures under the tank.













Spent the day installing the overflow.

Eshopps nano overflow





I thought a mag 5 would push under 200gph at 6 feet of head, 200gph being te limit for the overflow. But the mag 5 was pushing more than that so I added a sort of manifold to the return, that way the overflow is not overpowered and the mag 5 isn't being held back. Planning on using the manifold for a reactor later on.



This valve controls the flow of the return, if I close it the manifold pushed out more water.



The standard drain on the overflow was noisy. Looked up a couple of gurgle busting designs but it didn't help, I must've done it wrong. I toyed around with pvc until this design gave me a pretty much smooth and quite drain.




Submit "Pictures of my tank" to Digg Submit "Pictures of my tank" to del.icio.us Submit "Pictures of my tank" to StumbleUpon Submit "Pictures of my tank" to Google

Categories
‎ Uncategorized

Comments

  1. Alaska_Phil's Avatar
    Looks like a nice set up. How did you end up with your sump water level 6 ft below your tank water level?
  2. diablo30xp's Avatar
    Where did u find that design at? I am looking for one. The gurgle buster design u have.
  3. Reefdaddy's Avatar
    Try a maggie Muffler, they silence a gurgly OF. Nice tank so far man Is that a RK lite or elite?
  4. sedor's Avatar
    Hmmm never seen an overflow like that. My only concern would be that if your tank suffers from a hair algae outbreak or something similar it looks like those holes might get clogged up pretty quickly. Otherwise nice setup.
  5. Blennymower's Avatar
    @Alaska_Phil - The water level of the sump in the skimmer section is about 9 inches.

    @diablo30xp - http://home.everestkc.net/jrobertson57268/HGB/ That's the design I was going for but I must have done it wrong because every once in a while it was giving me a flushing sound. It wasn't that quite; other people have had success with from what I see. Anyways, what you see in my photo is the result of me toying with the pvc until I got this design which is really quite. All I hear is the water falling.

    @Reefdaddy - Thanks, it's an RKL.

    @sedor - Thanks, that is a possible problem. Since you mentioned it I put in the prefilter in the overflow in case that does happen.
  6. MeVsTheWorld's Avatar
    Your set up looks very similar to mine. I have been using a gurgle buster for over a year, works great. Make sure you put 1/2" or larger holes or like stated you could end up with a blockage of some kind. I have 4 1/2" holes and it is really quiet. Algae never really grows in it due to no light. You should put your ball valve on the other T for excess water flow, as it is now your putting resistance on the pump (unless it's wide open)to alter flow which over time could be the demise of the pump. I literally have the same set up(sump & overflow) and to set and control return flow from my pump I just adjust the flow at the excess flow tube.
  7. Alaska_Phil's Avatar
    Nice looking set up. Are those glass baffles in the sump? I've always been nervous about trying to cut glass myself.

    Add a piece of airline tube down through the vent in the top of your gurgle buster, you can adjust the height and really cut down on the remaining sound.
  8. Blennymower's Avatar
    @Alaska_Phil - The baffles are made of glass. I didn't cut them myself. My LFS cut them for me. The cap on my overflow is a hole for airline tubing but for some reason it does nothing.
  9. bleachandvomit's Avatar
    Not trying to bash you, but I would put the Vortech controller outside the stand or on the wall, I had mine like yours is and the moisture caused it to fry. Ecotech doesn't honor their warranty for water or moisture damage.

    Just looking out for you, take it or leave it!
  10. sedor's Avatar
    I've been running my electrical gear in my stand for over a year now and have yet to have any problems (crossing my fingers). I have to be honest though, i've been meaning to somehow move it outside the tank for some time just because i'm paranoid, but it all looks so neat and tidy tucked into the sump. If your stand has any ventilation at all you "should" be alright, but don't blame me when your equipment fries