View RSS Feed

melev

Hanging the Radion fixture

Rating: 13 votes, 5.00 average.
With the 60g on the stand, leveled and positioned near the wall - I left a small gap behind the tank to avoid salt-creep damage to the sheetrock - I needed to determine where to hang the Radion LED fixture over the tank. Using a 4' level, I placed it across the tank and set the light fixture on top. This permitted measuring the fixture from all four sides to get it centered. Hence, I was able to ascertain the distance from the rear wall and the right wall precisely for the hanging kit.

Name:  radion-centered.jpg
Views: 3196
Size:  208.5 KB


The Radion Hanging kit comes with a paper template. Holding the template on the ceiling, I moved it into place by putting the targets at the predetermined measured points. 9" from the right wall, 13.25" from the back wall. Thumb tacks were pressed through the bullseyes, essentially marking the ceiling with two tiny dots.

Name:  radion-hanging-kit-2.jpg
Views: 3060
Size:  126.5 KB


A quick visual to double check that it looked right, I tried to align those thumb tacks with the center of the Radion hangers before proceeding. It looked perfect and I was ready to proceed.

Name:  radion-hanging-kit.jpg
Views: 3145
Size:  161.4 KB


The kit came with screws, cabling, and adjustable hangers. It came with the ceiling connectors, but not any type of anchors, mollies, or butterfly toggle bolts. What I had in my garage are called SnapSkru wall anchors. They are very easy to install and hold nicely.

Name:  radion-hanging-kit-3.jpg
Views: 3022
Size:  148.5 KB


Name:  radion-hanging-kit-4.jpg
Views: 3003
Size:  128.2 KB


To install one, use a Phillip's head screwdriver, preferably with a drill.

Name:  radion-hanging-kit-6.jpg
Views: 2963
Size:  106.0 KB


Place it against the sheetrock, and pull the trigger slowly to let it carve its way into the drywall.

Name:  radion-hanging-kit-7.jpg
Views: 2971
Size:  189.3 KB


Name:  radion-hanging-kit-8.jpg
Views: 2888
Size:  173.9 KB


If some day this anchor needs to go, it can be unscrewed out of the drywall and quickly patched with spackling paste.

The hanging kit didn't include the screw to hold it into the anchor, but I had that as well. A 1" panhead steel screw was used to secure the threaded hanger piece. So, keep that in mind that you'll need some type of anchor and screw in addition to the Ecotech Radion Hanging kit.

Name:  radion-hanging-kit-5.jpg
Views: 3228
Size:  132.5 KB


I should have mentioned that if you are working over your tank to install something, cover it from any falling pollutants. I used a big towel to catch the drywall bits falling down.

I threaded the cable through the slotted cap for each screw. One end of the cable has a large aluminum stopper that rests inside the cap, and the other end is bare to feed into the adjustable hanger on the light fixture. The reason the cap is slotted is for installations on angled ceilings.

Name:  radion-hanging-kit-9.jpg
Views: 2886
Size:  252.2 KB


The slotted caps screw on to the threaded section.

Name:  radion-hanging-kit-10.jpg
Views: 3581
Size:  171.9 KB


The screws and loop tether were bolted to the light itself before I installed the ceiling hangers. The kit included the allen wrench.

Name:  radion-connections.jpg
Views: 3004
Size:  93.0 KB


The cables dangling from the ceiling were inserted into these adjustable hangers, and fed out the side.

Name:  radion-connections-7.jpg
Views: 2999
Size:  112.6 KB


I had some help getting this part done. If you don't have a second person, place the light on a supporting cross board to get the cabling inserted. Once done, you simply pull the cable as you lift the light up the cable - one side at a time. To lower it, press the tiny button near the top downward into the steel adjustor, and it will begin to slide downward.

Name:  radion-connections-2.jpg
Views: 2836
Size:  131.3 KB


The power cord does create some imbalance, so I used a sticky & ziptie to tether it to the tank and eliminate the drag.

Name:  radion-connections-3.jpg
Views: 2830
Size:  164.5 KB


The light is hanging perfectly level now.

Name:  radion-connections-4.jpg
Views: 2895
Size:  125.6 KB


The extra cable is coiled up for now, but I'll cut that off and put some crimp-stoppers on the ends to avoid any accidents in the future.

Name:  radion-connections-5.jpg
Views: 2782
Size:  153.1 KB


Name:  radion-connections-6.jpg
Views: 2975
Size:  180.9 KB


And it looks great.

Submit "Hanging the Radion fixture" to Digg Submit "Hanging the Radion fixture" to del.icio.us Submit "Hanging the Radion fixture" to StumbleUpon Submit "Hanging the Radion fixture" to Google

Categories
Lighting

Comments

  1. cyano's Avatar
    that looks very nice, can't wait to see more from this tank and the future masterpiece
  2. melev's Avatar
    They are pretty much going up at the same time but I'll be doing blog entries about specific topics rather than a mash-up of stuff.
  3. diablo30xp's Avatar
    how high off the water do u have hanging and whats the intensity u have it at?
  4. melev's Avatar
    It is 8" off the water and running at 85%.

  5. Aquarius Marinus's Avatar
    Neat! Does the Radion support automatic length of day changes with seasons like the Apex controller does?
    Does the grayed out "Lunar Phases Enabled" indicate that you have them enabled or disabled? If disabled, why did you choose to do so?
  6. melev's Avatar
    I have it enabled. I'm not sure about the length of days part - it never even popped in my mind. I'm a clock watcher, and pick my hours by preference rather that growing longer days for summer and shorter winter days.